Basic Router CLI Show Command

General Use

No.	Perintah Penuh	Perintah Singkat	Maksud Perintah
1	Show running-config	Sh run	Mengetahui konfigurasi yang aktif didalam DRAM (dynamic random acces memory
2	Show startup-config	Sh start	Mengetahui konfigurasi yang sudah tersimpan didalam NVRAM
3	Show version	Sh ver	Menampilkan informasi tentang versi software yang sedang berjalan lengkap dengan informasi hardware dan device

Routing Related

No.	Perintah Penuh	Perintah Singkat	Maksud Perintah
1	Show ip protocols	Sh ip prot	Untuk menampilkan ip protokol
2	Show ip route	Sh ip rout	Menampilkan konfigurasi routing

 

Interface Related

No.	Perintah Penuh	Perintah Singkat	Maksud Perintah
1	Show interfaces	Sh int	Untuk menampilkan statistic semua interfaces router
2	Show ip interfaces brief	Sh ip int bri	Memerinsa status atau kondisi dari tiap-tiap interface yang telah dikonfigurasi
3	Show protocols	Sh prot	Menampilkan status interface baik secara global maupun khusus dari protocol layer 3 yang terkonfigurasi

Connectivity Related

No.	Perintah Penuh	Perintah Singkat	Maksud Perintah
1	Show cdp neightbors	Sh cdp neig	Menunjukan tentang informasi semua piranti cisco tetangga yaitu switch dan router
2	Show session	Sh sess	Memperlihatkan sesi yang ada sekarang
3	Show ssh	Show ssh	Untuk melihat koneksi ssh
4	Ping	Ping	Mengecek koneksi
5	Traceroute	Tr	Untuk menentukan jalur terbaik

 

Konfigurasi pada Router 1

         --- System Configuration Dialog ---

Continue with configuration dialog? [yes/no]: no

Press RETURN to get started!

Router>ena

Router#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#line vty 0 4
Router(config-line)#password rere
Router(config-line)#transport input rere
Router(config-line)#login
Router(config-line)#end

Router#conf t

Enter configuration commands, one per line.  End with CNTL/Z.

Router(config)#int fa0/0

Router(config-if)#ip add 192.168.1.1 255.255.255.0

Router(config-if)#no shut

%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up

Router(config-if)#exit

Router(config)#int se2/0

Router(config-if)#ip add 192.168.2.1 255.255.255.0

Router(config-if)#clock rate 64000

Router(config-if)#no shut

%LINK-5-CHANGED: Interface Serial2/0, changed state to up

Router(config-if)#exit

Router(config)#

%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial2/0, changed state to up

Router(config)#router rip

Router(config-router)#version 2

Router(config-router)#network 192.168.1.0

Router(config-router)#network 192.168.2.0

Router(config-router)#exit

Router(config)#exit

Router#

%SYS-5-CONFIG_I: Configured from console by console

Konfigurasi pada router 2

         --- System Configuration Dialog ---

Continue with configuration dialog? [yes/no]: no

Press RETURN to get started!

Router>ena

Router#conf t

Enter configuration commands, one per line.  End with CNTL/Z.

Router(config)#int fa0/0

Router(config-if)#ip add 192.168.3.1 255.255.255.0

Router(config-if)#no shut

%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up

Router(config-if)#exit

Router(config)#int se2/0

Router(config-if)#ip add 192.168.2.2 255.255.255.0

Router(config-if)#no shut

%LINK-5-CHANGED: Interface Serial2/0, changed state to up

Router(config-if)#exit

Router(config)#

%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial2/0, changed state to up

Router(config)#router rip

Router(config-router)#version 2

Router(config-router)#network 192.168.2.0

Router(config-router)#network 192.168.3.0

Router(config-router)#exit

Router(config)#exit

Router#

%SYS-5-CONFIG_I: Configured from console by console

setting ip Pc 1

ip : 192.168.1.2

sm : 255.255.255.0

dg : 192.168.1.1

setting ip Pc 2

ip : 192.168.3.2

sm : 255.255.255.0

dg : 192.168.3.1