Sabtu, 07 April 2012


Basic Router CLI Show Command
General Use
No.
Perintah Penuh
Perintah Singkat
Maksud Perintah
1
Show running-config
Sh run
Mengetahui konfigurasi yang aktif didalam DRAM (dynamic random acces memory
2
Show startup-config
Sh start
Mengetahui konfigurasi yang sudah tersimpan didalam NVRAM
3
Show version
Sh ver
Menampilkan informasi tentang versi software yang sedang berjalan lengkap dengan informasi hardware dan device

Routing Related
No.
Perintah Penuh
Perintah Singkat
Maksud Perintah
1
Show ip protocols
Sh ip prot
Untuk menampilkan ip protokol
2
Show ip route
Sh ip rout
Menampilkan konfigurasi routing

 
Interface Related
No.
Perintah Penuh
Perintah Singkat
Maksud Perintah
1
Show interfaces
Sh int
Untuk menampilkan statistic semua interfaces router
2
Show ip interfaces brief
Sh ip int bri
Memerinsa status atau kondisi dari tiap-tiap interface yang telah dikonfigurasi
3
Show protocols
Sh prot
Menampilkan status interface baik secara global maupun khusus dari protocol layer 3 yang terkonfigurasi

Connectivity Related
No.
Perintah Penuh
Perintah Singkat
Maksud Perintah
1
Show cdp neightbors
Sh cdp neig
Menunjukan tentang informasi semua piranti cisco tetangga yaitu switch dan router
2
Show session
Sh sess
Memperlihatkan sesi yang ada sekarang
3
Show ssh
Show ssh
Untuk melihat koneksi ssh
4
Ping
Ping
Mengecek koneksi
5
Traceroute
Tr
Untuk menentukan jalur terbaik


 
Konfigurasi pada Router 1
         --- System Configuration Dialog ---

Continue with configuration dialog? [yes/no]: no

Press RETURN to get started!

Router>ena
Router#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#line vty 0 4
Router(config-line)#password rere
Router(config-line)#transport input rere
Router(config-line)#login
Router(config-line)#end

Router#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#int fa0/0
Router(config-if)#ip add 192.168.1.1 255.255.255.0
Router(config-if)#no shut

%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up

Router(config-if)#exit
Router(config)#int se2/0
Router(config-if)#ip add 192.168.2.1 255.255.255.0
Router(config-if)#clock rate 64000
Router(config-if)#no shut

%LINK-5-CHANGED: Interface Serial2/0, changed state to up

Router(config-if)#exit
Router(config)#
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial2/0, changed state to up

Router(config)#router rip
Router(config-router)#version 2
Router(config-router)#network 192.168.1.0
Router(config-router)#network 192.168.2.0
Router(config-router)#exit
Router(config)#exit
Router#
%SYS-5-CONFIG_I: Configured from console by console

Konfigurasi pada router 2

         --- System Configuration Dialog ---

Continue with configuration dialog? [yes/no]: no

Press RETURN to get started!

Router>ena
Router#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#int fa0/0
Router(config-if)#ip add 192.168.3.1 255.255.255.0
Router(config-if)#no shut

%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up

Router(config-if)#exit
Router(config)#int se2/0
Router(config-if)#ip add 192.168.2.2 255.255.255.0
Router(config-if)#no shut

%LINK-5-CHANGED: Interface Serial2/0, changed state to up
Router(config-if)#exit
Router(config)#
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial2/0, changed state to up

Router(config)#router rip
Router(config-router)#version 2
Router(config-router)#network 192.168.2.0
Router(config-router)#network 192.168.3.0
Router(config-router)#exit
Router(config)#exit
Router#
%SYS-5-CONFIG_I: Configured from console by console

setting ip Pc 1
ip : 192.168.1.2
sm : 255.255.255.0
dg : 192.168.1.1

setting ip Pc 2
ip : 192.168.3.2
sm : 255.255.255.0
dg : 192.168.3.1